Skip to main content

TL;DR: FPLP is plenum-rated power-limited fire alarm cable, FPLR is riser-rated, and FPL is general purpose. A higher rating can replace a lower one (FPLP for FPLR or FPL, FPLR for FPL), never the reverse, and NEC Article 760 also lets certain communications cables such as CMP and CMR substitute. Pick the rating by the spaces the run passes through, and confirm with the adopted NEC edition, NFPA 72, the panel manufacturer, and the AHJ.

Fire alarm cable ratings come up at the counter every week, and a wrong jacket is easy for an inspector to spot. The rating follows the space the cable passes through, not the job budget. Here is the hierarchy, plus the substitution, shielding, CI, and gauge questions that follow it.


The hierarchy in one table

Power-limited fire alarm (PLFA) cable comes in three fire-resistance ratings: FPLP for plenums, FPLR for risers, and FPL for general-purpose runs. Each is tied to a flame test, and cable that passes a tougher test can go where a lower rating is allowed.

Rating Name Typical use Flame test (listed to UL 1424) Can stand in for
FPLP Power-limited fire alarm, plenum Ducts, plenums, and other spaces used for environmental air NFPA 262 (UL 910 tunnel test) FPLR and FPL
FPLR Power-limited fire alarm, riser Vertical runs in shafts and floor to floor UL 1666 riser test FPL
FPL Power-limited fire alarm General-purpose runs UL 1581 vertical flame test No other FPL type

Permitted uses and exceptions depend on the NEC edition your jurisdiction has adopted. Confirm with the AHJ.

FPL cannot go up a riser or into a plenum, and FPLR cannot go into a plenum.


Match the rating to the space

Choose the cable by the most demanding space the run passes through. A circuit that rises through a shaft and then crosses a return-air ceiling needs a rating (or wiring method) that covers the return-air ceiling.

  • Plenum and air-handling spaces. If the space above a drop ceiling is used for return air, it is an air-handling space and FPLP is the usual answer. If the ceiling cavity is not used for environmental air, FPL may be acceptable. The ceiling tile does not decide it; how the space moves air does. Check the mechanical drawings and ask the AHJ.
  • Vertical risers. Runs in a shaft or passing floor to floor call for FPLR or FPLP.
  • General-purpose runs. Other runs can use FPL, FPLR, or FPLP.

The adopted NEC also allows some runs in raceway instead of higher-rated cable. Those allowances vary by edition, so confirm with the AHJ before you count on one.


Substitutions under NEC Article 760

Higher-rated cable may substitute for lower-rated cable, and NEC Article 760 lists certain communications cables as permitted substitutes for PLFA cable. Newer NEC editions reorganized the cable rules, so check the edition your jurisdiction enforces.

Required rating Permitted substitutes (as commonly listed)
FPLP CMP
FPLR CMP, FPLP, CMR
FPL CMP, FPLP, CMR, FPLR, CMG, CM

Summary of the NEC Article 760 substitution table in recent editions. Verify against your adopted edition.

Higher-rated cable can generally replace lower-rated cable when it meets the applicable NEC requirements. When the specified cable isn’t available, a properly listed, higher-rated cable (FPLP in place of FPLR or FPL, for example) can keep a job moving without compromising code compliance. Confirm the substitution against the locally adopted code and the project requirements before installation.

Before you substitute:

  • Check the panel manual. The manufacturer may set conductor size, twisting, shielding, or capacitance limits a given data cable does not meet.
  • Check the spec. Many specifications call for fire alarm cable by name, and the spec can be stricter than the code.

Shielded vs. unshielded

Use shielded fire alarm cable when the panel manufacturer calls for it or when the run passes near heavy electrical noise. Unshielded cable is common, but some manufacturers require or recommend shielded cable for certain circuits, such as some addressable signaling line circuit (SLC) loops and speaker circuits. Shielding also deserves a look on runs near motors, variable-frequency drives, generators, elevator equipment, or long parallel runs with power wiring.

A shield helps when it is terminated the way the manufacturer says, commonly grounded at the panel end with the drain wire carried continuously through each device. Grounding it at both ends, or leaving it unterminated, can defeat the purpose. Follow the panel installation manual.


Circuit integrity (CI) cable

CI cable is fire-resistive cable listed to keep a circuit working for a rated period, typically 2 hours, during a fire. It shows up when NFPA 72 or the project requires pathway survivability, most often on emergency voice/alarm communication systems in buildings that use partial evacuation or move occupants to protected areas.

NFPA 72 defines pathway survivability levels. In broad terms:

  • Level 1: Pathways in metal raceway or metal armored cable in a fully sprinklered building.
  • Level 2: 2-hour fire-rated cable (such as 2-hour CI cable), a 2-hour rated cable system, or a 2-hour rated enclosure.
  • Level 3: Level 2 protection plus a fully sprinklered building.
  • Level 4: 1-hour fire-rated cable or enclosure, added in the 2022 edition of NFPA 72.

The required level depends on the evacuation strategy and the building. A 2-hour rating holds up when the cable is installed per its listing, including the supports and raceway tested with it. CI cable carries a “CI” suffix in its marking. Read the spec, the NFPA 72 edition the AHJ enforces, and the manufacturer’s instructions before you order.


Gauge and voltage drop on NAC circuits

Gauge matters on notification appliance circuits (NAC) because the current horns and strobes draw causes voltage drop over the length of the run. If the last appliance sees less voltage than its listed operating range, it may not flash or sound as designed.

Drop rises with current and distance and falls as the conductor gets larger. This comparison uses copper resistance values from NEC Chapter 9 and treats the full load as sitting at the end of the run (a conservative shortcut):

Conductor Approx. resistance (ohms per 1,000 ft) Drop: 1.5 A at 300 ft (600 ft of wire, out and back)
16 AWG 4.89 About 4.4 V
14 AWG 3.07 About 2.8 V
12 AWG 1.93 About 1.7 V

For illustration. Uncoated solid copper at 75 degrees C. Real NAC calculations use the panel’s minimum output voltage, the appliances’ listed ratings, and the panel manufacturer’s calculation method or software.

Many 24 V notification appliances list an operating range down to about 16 V, and panel output is lower at the end of battery standby than on AC power. Designers calculate drop from the panel’s worst-case output, not from 24 V. That same standby condition drives battery sizing, which our fire alarm battery backup calculations guide walks through.


Jacket color is not the rating

Red is a convention for fire alarm cable, not the rating. The printed jacket marking (FPLP, FPLR, FPL, or a multi-listed legend) is the rating, and it is what the inspector reads.

Neither NEC Article 760 nor NFPA 72 uses color to define fire alarm cable. A red jacket marked CM is still CM, and many cables carry several listings (one Southwire shielded cable prints CMR, CL3R, and FPLR). Some specifications and AHJs do call for red so fire alarm wiring is easy to identify, so check the spec before ordering another color.


What to bring to the counter

Describe the spaces, the circuits, and the distances, and the right cable gets easier to pick. Your SDS franchise team can match ratings, gauge, and shielding when they know:

  • Spaces the run passes through. Return-air ceilings, risers, general areas, and wet conditions.
  • Circuit types. SLC, initiating device circuits, NAC, speaker circuits, and auxiliary power.
  • Run lengths and loads. Longest NAC run and the appliance count on it.
  • Panel manufacturer wiring requirements. Gauge, twisting, shielding, and capacitance or resistance limits.
  • The project specification. Survivability level or CI cable, required manufacturers, jacket color, and listings.

Security Data Supply franchises carry fire alarm cable from West Penn Wire, Southwire, Genesis, Comtran, and Vertical Cable; stock can vary by franchise. Browse Fire and Wire & Cable, and run the fire alarm installation checklist and the most common fire installation mistake before you pull.

Bring your floor plan, circuit list, and panel manual to your SDS franchise team, and leave with cable rated for every space on the run.

Find Your Local SDS


Frequently asked questions

What is the difference between FPL, FPLR, and FPLP cable?

They are the three fire-resistance ratings for power-limited fire alarm cable under NEC Article 760: FPLP for plenums and air-handling spaces, FPLR for risers, and FPL for general-purpose runs. A higher rating can be used where a lower one is allowed.

Can I use FPLR in a plenum space?

No. FPLR is riser-rated and does not meet the plenum requirement. Use FPLP, a permitted substitute such as CMP, or a wiring method the adopted NEC allows, and confirm with the AHJ.

What fire alarm cable do I need for a drop ceiling?

It depends on whether the space above the ceiling handles environmental air. A return-air plenum typically calls for FPLP or a permitted substitute or wiring method. If the cavity is not an air-handling space, FPL may be acceptable. Check the mechanical drawings, the spec, and the AHJ.

Can CMP or CMR cable substitute for fire alarm cable?

NEC Article 760 lists communications cables as permitted substitutes: CMP for FPLP, CMP or CMR for FPLR, and CMP, CMR, CMG, or CM for FPL. Confirm the table in your adopted NEC edition, since the panel manufacturer or spec may still require fire alarm cable.

When is shielded fire alarm cable required?

Shielded cable is required when the panel manufacturer or project spec calls for it, as some do for addressable SLC loops and speaker circuits. Consider it near motors, drives, and generators too, and terminate the shield as the manufacturer instructs.

What is circuit integrity (CI) cable and when do I need it?

CI cable is fire-resistive cable listed to keep a circuit operating for a rated period, typically 2 hours, during a fire. It is used when NFPA 72 or the spec requires pathway survivability, most often on emergency voice/alarm systems, and must be installed per its listing.

Does fire alarm cable have to be red?

No. Red is an industry convention; the printed jacket marking defines the rating. Some specs and AHJs require red for easy identification, so check before ordering another color.


About the author

Ron Broussard is Chief Executive Officer of Security Data Supply and has more than 30 years of experience in the security industry. He has held executive leadership roles across distribution and manufacturing, giving him a broad perspective on the challenges contractors, integrators, and distributors face every day. At Security Data Supply, he guides the company’s franchise network, vendor relationships, and long-term growth strategy.

Methodology

This guide draws on Security Data Supply’s distribution experience with fire alarm contractors, NEC Article 760 as summarized by code educators, NFPA 72 pathway survivability guidance, and cable manufacturer literature. It teaches the rating system and is not a code interpretation. Code editions, local amendments, project specifications, and panel manufacturer requirements vary, and stock can vary by franchise. Confirm requirements with the adopted NEC edition, NFPA 72, the panel and cable manufacturers, the project specification, and the AHJ before installation.

Sources and further reading